CARTEK_Motorsport_Power_Distribution_Module_Unit_only_R_R32_VR6_S3_RS3_TT_RS_01_thd
cartek, , , , , ,
CARTEK Motorsport Power Distribution Module (Unit only) R R32 VR6 S3 RS3 TT RS
CARTEK Motorsport Power Distribution Module (Unit only) R R32 VR6 S3 RS3 TT RS
CARTEK Motorsport Power Distribution Module (Unit only) R R32 VR6 S3 RS3 TT RS

CARTEK Motorsport Power Distribution Module (Unit only) R R32 VR6 S3 RS3 TT RS
CARTEK Motorsport Power Distribution Module (Unit Only). Brand New Genuine Cartek Motorsport Power Distribution Module (Unit Only). Designed to replace the functions of fuses, circuit breakers and relays in one small, fully electronics unit. Cartek’s Power Distribution Module is ideal for race cars and motorcycles which have minimal onboard electrical circuits but still require rugged and reliable protection and control. Simple connections and no configuration procedures makes this system very easy use and quick to install. The 4 x 10 amp outputs can be used to control power to various devices such as ECUs, instrumentation, lighting, starter solenoid, radiator fan, etc. Channels will automatically shut down if a short circuit or over-current is detected – LED Status indication on the PDM and Cartek Switch Panels makes fault finding simple. The Cartek Power Distribution Module Kit is a direct replacement for 4 x 10amp Fuses, 4 Relays and 4 Switches. This unit therefore reduces all the wiring in between the Fuses, Relays and Switches as well as simplifying the installation. When mounting the PDM, electrical contact must be made between the vehicle’s chassis/earth and the metal case of the PDM at its mounting points. 12v Power Input is supplied to the PDM via the M6 electrical stud. Power Output connections are made using 6.3mm spade terminals. Each channel is turned ON by connecting the corresponding channel signal wire to chassis/earth. Connection can be made using dashboard switches, oil pressure switches, thermo-switches, etc. When a Cartek Switch Panel (pushbutton switches with integrated LED) is used then the LED will display the channel status. No LED = Channel OFF LED on = Channel ON Flashing = ERROR. When short-circuit or over current is detected, the PDM will shut down that channel and the corresponding LED will begin to flash. To reset the error, switch the channel OFF then ON again. TECHNICAL DATA SIZE: L = 90mm W=42mm WEIGHT: 80g POSITIVE POWER TERMINAL: M6 BRASS STUD CHANNEL OUTPUT CONNECTIONS: 6.3mm MALE SPADE TERMINALS OPERATIONAL VOLTAGE: 7V-18V POWER SWITCHING CURRENT: 10A MAX EACH CHANNEL CURRENT CONSUMPTION: 0.02A (NO LOAD) OPERATING TEMPERATURE: -10°C – +85°C. Check out the shop for more 1000s more Performance & Genuine OEM Parts. Get news of New Parts to your inbox. Christmas Advent & Gifts. CARTEK Motorsport Power Distribution Module (Unit only) R R32 VR6 S3 RS3 TT RS. Choosing the right Air Lift Kit. Car Gaming Racing Simulators. Cold Air Induction Kits. Electrical & Engine Parts. Anti Roll Bar Kits. 10mm HT Ignition Leads. All other Non VW Parts. RC + Scale Models. For 1000s more of the best available parts. The item “CARTEK Motorsport Power Distribution Module (Unit only) R R32 VR6 S3 RS3 TT RS” is in sale since Tuesday, March 20, 2018. This item is in the category “Vehicle Parts & Accessories\Car Tuning & Styling\Electrical Components\Performance Switches & Relays”. The seller is “vw-parts-international” and is located in UK. This item can be shipped worldwide.
  • Brand: Cartek
  • Manufacturer Part Number: N / A

CARTEK Motorsport Power Distribution Module (Unit only) R R32 VR6 S3 RS3 TT RS